Dilunett - Gel remover for all surfaces - Owatrol

Dilunett - Gel remover for all surfaces - Owatrol

Easily remove all traces of residue with Dilunett stripper and its water -based formula which guarantees a more resistant surface and better adhesion of the new coating.

Quick and efficient, it breaks down the coating to be removed (paints, varnishes, glues…) then rinses effortlessly to leave you with a clean surface ready to be repainted.
Ideal for your DIY and home-staging projects.
Removes stains, waxes, varnishes, paints and antifouling paints.

Properties :

• Solvent-free and paraffin-free gel - non-flammable.
• Makes the coating water-soluble (water rinse).
• Effective, removes up to 8 layers of paint in one application.
• Easy to use, it works on its own even in the most difficult-to-access places.
• It does not evaporate, it does not dry out.

Recommendations before application:

• Always carry out a preliminary test.
• Equip yourself with rubber gloves, a nylon brush or a glue brush.
• The contact time varies from a few minutes to several hours depending on the type of coating (glycerophthalic or acrylic) and the number of coats. Check its action using a spatula.
• Since stripping is never neutral, on wood it is imperative to neutralize with Net-Trol.

Application :

1. Apply a thick layer of Dilunett to the entire surface to be stripped.
2. Allow the product to work.
3. If it dries out, reactivate by spraying with a fine mist of water.
4. Rinse with clean water using a brush or a low-pressure cleaner.
   Using hot water makes elimination easier.
5. After stripping wood, always apply Net-Trol (on wet wood) and do so IMMEDIATELY after rinsing off the Dilunett.
6. Refer to the operating instructions on the packaging.
7. Corrosive product, read the precautions for use before use.

Destination :

• Outside.
• Applicable to wood**, metal***, plastic, stone, cement...
• Ideal for hard-to-reach or highly ornate parts, horizontal or vertical: doors, gates, barriers...
• Recommended for stripping large surfaces - non-volatile, does not dry out and remains active for a long time.
• Does not attack plastics, rubbers, synthetic coatings or gelcoats.

** except Oak, Chestnut and marquetry

*** except aluminum

Packaging:

0.5 L, 1 L, 2.5 L and 10 L.

FAQ - Frequently Asked Questions

1. Is Dilunett suitable for all types of wood?
   Yes, Dilunett can be used on softwood, hardwood, or exotic woods without damaging the fibers. It is even recommended before applying Owatrol oils.
2. Can it be used indoors?
   Yes, its formula without strong odor and without harmful solvents makes it perfectly suited for indoor work.
3. How many layers of paint can it remove?
   Depending on the thickness, Dilunett can remove up to 8 layers in a single application.
4. Is it dangerous for the environment?
   No, its formula is biodegradable and rinses easily with water. 5.
5. Can it be used on rusty metal?
   Yes, on oxidized metal, after stripping, it is advisable to apply Owatrol Oil to stabilize the rust.
6. What should I do if the product dries out?
   Simply re-moisten the surface with Dilunett or a water spray to reactivate the gel action.
7. Is sanding necessary after stripping?
   Light sanding can be helpful to achieve a perfectly smooth surface, but it is not mandatory.
8. What is the yield?
   Approximately 4 to 6 m² per litre, depending on the thickness of the coating to be stripped.
9. Can it be used to remove wood stain? Yes, Dilunett is very effective on film-forming or old wood stains.
10. How long should it be left to dry after rinsing?
    Generally, wood: 24 to 48 hours. Metal/stone/concrete: 12 hours.