New products
All New Products
      PU010 - PU adhesive foam for insulation panels - Illbruck
      • PU010 - PU adhesive foam for insulation panels - Illbruck
      • PU010 - PU adhesive foam for insulation panels - Illbruck

      PU010 - PU adhesive foam for insulation panels - Illbruck

      Mono-component polyurethane foam, which expands and hardens with the humidity of the air and the support, to very easily achieve a bonding that is both powerful and permanent, but also thermal and acoustic insulation.

      Packaging:
      22 Items
      €20.13Tax Included
      €20.54- 2%

      Volume discounts

      QuantityYou SaveUnit price
      63 %€19.92
      125 %€19.51
      ILL 2030003
      8713465297503

      PU010 - PU adhesive foam for insulation panels - Illbruck

      PU010 is a single-component polyurethane foam, which expands and hardens with the humidity of the air and the support, to very easily achieve a bonding both powerful and permanent, but also thermal and acoustic insulation.

      Scope: 

      • The bonding of insulating panels (PSE, PU) as part of an external insulation system (ITE); an aerosol sticks about 4 to 6 m² of insulating panels.
      • The bonding of insulating panels in concrete cellars.
      • Various applications of bonding and thermal and acoustic insulation.
      • The recapping of small cavities.

      Advantage: 

      • Aerosol equipped with the 2-in-1 system: manual or pistolable use.
      • Replaces the glue mortar (1 aerosol vs 1 bag of glue).
      • Powerful and permanent bonding.
      • Versatile: indoor and outdoor.
      • Charging: 3 hours.

      Preparation:

      • PU010 must be used at an ambient temperature between +5°C and +35°C.
      • The aerosol must be at a temperature between +10°C and +30°C.
      • The supports must be strong, dusted and degreased.
      • Moisten the adhesion surfaces to obtain a foam with a homogeneous cell structure and faster hardening.
      • Shake the aerosol vigorously 20 to 30 times before use.
      • Do not apply in high winds.

      Implementation:

      Manual implementation: 

      • Remove the protection at the top of the aerosol.
      • Follow the explanations of the pictograms opposite.
      • To bring out the foam, press lightly on the valve; the amount of extruded foam can be dosed by more or less actuating the lever on the valve.

      Pistolable implementation: 

      • Remove the protection at the top of the aerosol.
      • Screw the aerosol thoroughly onto the gun. Use the green ring.
      • Dose the extrusion by lightly pressing the trigger of the gun and adjust the quantity with the adjustment screw.

      For the bonding of insulating panels:

      • Apply the foam on the inner surface of the insulating panel by extruding a cord of 3 to 4 cm in diameter on the periphery of the panel to be glued and about 3 cm away from the edge then a last cord in the shape of "W" inside (at least 40% of the panel will be covered with glue).
      • Wait 5 to 10 minutes (not exceeding 10 minutes) so that the glue develops a sufficient tack (suction cup effect).
      • Position the panel on the wall (the panel can be repositioned during the open time of the glue or about 10 minutes).
      • Cut off hardened foam residues.
      • The final resistance is obtained after 3 h. it is important to follow the instructions of the manufacturer of insulating panels.

      Hygiene and safety precautions: 

      • Work only in well-ventilated premises.
      • Do not smoke.
      • Wear protective clothing.
      • Protect the eyes and wear protective gloves.
      • Largely protect the working area with paper or plastic sheet.

      Cleaning: 

      • After use, clean quickly with the Illbruck AA290 cleaner either the valve and nozzle (for manual use) or the outside of the gun and its tip (for pistolable use).
      • Hardened foam can only be removed mechanically (cutter, sandpaper sanding, etc.). It is therefore strongly recommended to protect the floors, with plastic film or paper, in the work areas.

      Conditioning: 

      • Aerosol of 750 ml.

      Yield: 

      • An aerosol makes it possible to glue about 6 m2 of insulating panels.
      Illbruck
      ILL 2030003
      22 Items

      Data sheet

      Signal word
      DANGER
      Hazard statements
      H222 – Extremely flammable aerosol.
      H229 – Pressurised container: May burst if heated.
      H315 – Causes skin irritation.
      H317 – May cause an allergic skin reaction.
      H319 – Causes serious eye irritation.
      H332 – Harmful if inhaled.
      H332 – Harmful if inhaled.
      H335 – May cause respiratory irritation.
      H351 – Suspected of causing cancer.
      H373 – May cause damage to organs.
      Hazard pictogram
      Hazard pictogram : GHS02 - Flammable GHS02 - Flammable
      Hazard pictogram : GHS07 - Harmful GHS07 - Harmful
      Hazard pictogram : GHS08 - Health hazard GHS08 - Health hazard
       

      Specific References

      EAN13
      8713465297503

      Download

      PU010 - Illbruck

      Technical datasheet

      Download (225.09KB)

      Quelles sont les déclinaisons et prix pour PU010 - PU adhesive foam for insulation panels - Illbruck ?

      PU010 - PU adhesive foam for insulation panels - Illbruck - Déclinaisons, dimensions, prix, références
      Variante Packaging Prix HT Prix TTC Prix dès 6 pièces (-3%) (TTC) Prix dès 12 pièces (-5%) (TTC) Réference EAN-13 Stock* disponible
      PU010 - PU adhesive foam for insulation panels 0,75 L €17.12 €20.54 €19.92 €19.51 ILL 2030003 8713465297503 22 Pièce(s)
      *Stocks disponibles, sauf erreur ou omission, en nos entrepôts de Lille (France) ou Tournai (Belgique), livraison en 24h/72h - Enlèvement gratuit - Expédition à partir de 4,99 € en France, 3,99 € en Belgique selon poids, délai et transporteur.