MN Liquid Polish - Liquid wax for natural stone - Lithofin

MN Liquid Polish - Liquid wax for natural stone - Lithofin

Lithofin MN Polish is a special product for marble, natural and artificial stone.

It is a liquid polish that contains high-quality solvents and waxes.

The use of quality raw materials allows for the protection and maintenance of natural stone surfaces in a high-quality manner.

A glossy film appears from the first application. This shine can be enhanced with hand or machine polishing.

Lithofin MN Polish revives the colors of stone surfaces, improves their appearance, facilitates maintenance and makes them water-repellent.

Technical specifications:

• Density: approx. 0.9 g/cm³
• Flash point: >26°C (cc)
• pH: na
• Appearance: liquid, clear, colorless
• Scent: aromatic
• Water solubility: insoluble

Scope of application:

As a first treatment for natural stone and concrete floors, window sills, tables, etc. Gives a fresh look and protects.

It can also be used to revive coatings that have become dull and matte.

Inside, Lithofin MN Polish is used instead of traditional stone care products containing trichloroethylene or perchloroethylene.

It can be used on all polished or finely polished natural stone surfaces such as marble, limestone, travertine, slate, granite, etc., as well as concrete blocks and agglomerated marble.

Lithofin MN Polish resists all kinds of household dirt and salt. It is not resistant to cellulose lacquer thinner, gasoline, etc. Depending on the type of use, the effect can last for several months.

Instructions for use:

1. Shake the bottle lightly before use.
2. Apply a thin, even coat of Lithofin MN Polish with a clean cloth or felt-tip pen and allow to dry.
3. Then polish using a soft linen cloth or a polishing felt, by hand or machine.
4. Treat more absorbent surfaces several times in succession if necessary.

Caution: Surfaces to be treated must be completely dry. Do not use Lithofin MN Polish at temperatures below 15°C or above 25°C. Solvent-sensitive surfaces must be protected. Lithofin MN Polish is suitable for indoor use only. For best results, surfaces must be polished and smooth. Remove any rough areas with 000 steel wool or a nylon abrasive disc.

Lithofin MN Polish can be removed with or, in difficult cases, %C3% Lithofin %C3% .

Yield :

• approx. 10 to 20 m²/l depending on the surface area.

FAQ - Frequently Asked Questions

1. On which stones can I apply MN Liquid Polish?
   It is designed for all natural limestone or sensitive stones, such as marble, bluestone, travertine, terrazzo, etc. It is not recommended for granite or very hard surfaces requiring other types of treatment.
2. Does the product make the floor slippery?
   No, once properly applied and buffed, it leaves a satin sheen that is not slippery, even on an indoor floor.
3. Is it possible to use it outdoors?
   No, MN Liquid Polish is specifically designed for indoor use. Outdoors, the weather would damage the wax.
4. Does the product protect against stains?
   Yes, but in moderation. It creates a protective film that reduces dirt penetration. For more advanced stain protection, it is advisable to use Lithofin MN Fleckstop water repellent before waxing.
5. What maintenance is required after application?
   Regular cleaning with MN Wash & Clean is sufficient to preserve the glossy effect and protection.
6. How long does the effect of the polish last?
   Depending on the room's use, the protection can last from several weeks to several months. On high-traffic floors, regular renewal is recommended.
7. Does the product change the color of the stone?
   It slightly revives the hues, which accentuates the natural depth of the stone, without altering its original color.
8. Can MN Liquid Polish be applied to a surface that has already been treated?
   Yes, it can be added to a surface already protected by a water repellent or wax, as long as it is clean and dry.
9. How many coats should be applied?
   One coat for a natural satin effect. Two coats for a more intense shine.
10. How to remove the wax if needed?
    To strip an old coating, use Lithofin WAX-OFF or a detergent suitable for waxes.