Akepox 2020 - Construction Adhesive - Akemi

Akepox 2020 - Construction Adhesive - Akemi

2-component, semi-thick construction adhesive for filling thin joints and for vertical bonding of natural and artificial stones .
Good adhesion on metal and wet stones.

The cartridges guarantee a simple, reliable and clean job.
An exact and homogeneous mixture.

Features :

• Solvent-free
• Weather resistant
• Easy dosing and mixing thanks to the cartridge system adaptable to any standard gun
• Very little shrinkage during curing and minimal tension in the adhesive layer
• Bonding particularly resistant to weathering
• Good heat stability: approximately 60-70°C for filled bonds and approximately 100-110°C for standard bonds
• No deformation of the glue layer
• Good resistance to aging
• Excellent resistance to alkalis, and therefore recommended for bonding to concrete
• Recommended for use on gas-tight materials due to the absence of solvents.
• Good electrical insulation
• Good adhesion on slightly damp stones
• Recommended for solvent-sensitive materials, such as expanded polystyrene and ABS.
• The product does not tend to crystallize, so there are no storage problems and it is safe to use.
• Mixing ratio 2:1.

Use :

A: Cartridge System:

1. Thoroughly clean the surfaces to be glued and roughen them.
2. Remove the cartridge cap, insert the cartridge into the gun, operate the handle until material comes out of both openings, if necessary, attach a mixing nozzle.
3. The product can be coloured using AKEPOX colourants or concentrates (max. 5%).
4. If you use it without a mixing nozzle, the two components must be thoroughly mixed.
5. The mixture can be used for approximately 40 to 50 minutes (20°C).
   The bonded parts are transportable after 6 to 8 hours (20°C), loadable and machinable after 12 to 16 hours (20°C).
   Maximum strength after 7 days (20°C).
6. Tools can be cleaned with AKEMI Nitro Thinner.
7. Heat accelerates and cold delays the hardening reaction.

B: Boxed products

1. Thoroughly clean the surfaces to be glued and roughen them.
2. Mix 2 equal parts by weight or volume of glue with 1 equal part by weight or volume of hardener until a homogeneous color is obtained.
3. The product can be coloured using AKEPOX colourants or concentrates (max. 5%).
4. 4. The mixture can be used for approximately 40 to 50 minutes (20°C).
   The bonded parts are transportable after 6 to 8 hours (20°C), loadable and machinable after 12 to 16 hours (20°C).
   Maximum strength after 7 days (20°C).
5. Tools can be cleaned with AKEMI Nitro Thinner.
6. Heat accelerates and cold delays the hardening reaction.

Packaging:

3 kg, 22.5 kg and 180 ml cartridge.

FAQ - Frequently Asked Questions

1. Can AKEMI AKEPOX® 2020 be used to bond white marble?
   Yes, but it's important to consider that hardened adhesive tends to yellow when exposed to light or light-colored surfaces. If the joint or bonding area is visible and light-colored, it may be preferable to choose a very low-yellowing or transparent epoxy adhesive.
2. Can it be used outdoors in cold weather?
   Yes, it's suitable for outdoor use, as the product is weather-resistant. However, application should not be done below approximately 10°C, as the curing process will be insufficient.
3. What is the setting time before one can work/move on the glued element?
   At ~20 °C: approximately 6-8 hours for displacement, 12-16 hours for machining/loading, 7 days for maximum strength.
4. Can this glue be colored to match a stone or a joint?
   Yes. You can add a maximum of ~5% of AKEMI® color paste or concentrate to adjust the shade.
5. What types of materials can be glued with it?
   Natural stone (marble, granite, limestone), artificial stone, concrete, terrazzo, metal, fiberglass, wood, glass, rigid synthetic materials (hard PVC, ABS), etc. Caution – not suitable for PE, PP, silicone, soft PU, etc.
6. What safety precautions should be taken?
   Use gloves, eye protection, and a mask if necessary. stein.akemi.de Ensure correct mixing ratio (2:1). Do not work with the product if it has already thickened or gelled. Ensure good ventilation in the work area. Follow the safety data sheet.
7. How do I clean the tools after use?
   Clean tools immediately with AKEMI® Nitro-Thinner while the adhesive is still wet. Once hardened, it can no longer be removed with solvents, only mechanically or by high temperature (> 200 °C).