GRAFICSTAR Logo Doormat

GRAFICSTAR Logo Doormat

GRAPHICSTAR is the superior quality indoor doormat to beautify your entrances , lobbies, reception areas, etc. Personalize it to your image with your logo , design, message , slogan , etc.

• Premium tufted logo rugs offer superior color fastness and wash resistance .
• High-twist nylon thread resists crushing and traps dirt and moisture .
• Fade Resistant - Solution dyed nylon is waterproof and UV resistant .
• Printed on high twist tufted nylon .

Combine a maximum of 7 colors for the doormat including a maximum of 6 colors for the illustration from the 29 colors available and follow the instructions for transmitting your logo below.

Please indicate the external dimensions of the doormat OR the frame. We calculate the rest.

BE CAREFUL about the direction of travel.

PRESENTATION

The GRAFICSTAR doormat features your logo or design on solution-dyed, high-twist nylon.

It is recommended for indoor use at entrances, lobbies, reception counters or anywhere you want to display your logo , design , illustration , etc. to your visitors , employees or customers .

It is completely washable and offers a palette of 30 colors to create your design.

Specifications :

• YARN: Continuous filament dyed in type 6 nylon solution.
• YARN WEIGHT: 1,000 g/m².
• PILE THICKNESS: 11.3 mm.
• TOTAL WEIGHT: 3.20 kg/m².
• PRIMARY SUPPORT: 120 g/m² polyester spun non-woven.
• RUBBER BACKING: 100% Nitrile EXS rubber. Compression molded with reinforced edges for excellent dimensional stability and lay flat properties.

PLEASE NOTE: We offer a wide choice of colors for your projects, ramps, doormat frames, but also integrated scrapers or brushes, a harder surface, personalized stainless steel marking, a design choice for outdoors, etc. .. On Request or to see on our other pages.

THICKNESS AND EDGE FINISH:

• ± 8 mm with 1.5 cm rubber edge (standing doormat)
• ± 10 mm without edge (built-in doormat)

The ±10mm doormat without edge can be placed in a pit and surrounded by a doormat frame.

The 1.5 cm wide rubber edge has a thickness of 3 mm.

DOORMAT UNDERLAYER:

The doormat is available in 2 different underlays.

1. Smooth sole: A smooth rubber sole.
2. Claw sole: A sole raised by "nubs" ideal for dirty places, on slopes or any other place where grip is not optimal.

INSTRUCTION WHEN SENDING YOUR IMAGE-PHOTO-LOGO

NOTE: All projects are checked before studies and production of a “PROOF” proof.

Only YOUR VALIDATION of the “PROOF” triggers the production of your carpet, then preparation for shipment. Please note, no corrections can be made after validation and production of the BAT.

Instructions for obtaining the BAT after ordering:

1. You must take into account the dimensions ordered and the proportions of your sketch.
2. Your image should, if possible, be provided with the exact dimensions of the project (and in good definition)
3. You send us by email an image/photo of your project in JPG format (this is classic), PDF, PNG, PSD, TIFF, PNG or AI
4. You tell us the maximum 7 colors you want, clearly indicating which color for which use.
5. The image is uploaded by our computer graphics department and checked.
6. The image is resized following your ordered exterior dimensions. It is reduced, where applicable, by the thickness of the frame or the rubber edge
7. A BAT test is sent to you by email and/or to your customer account
8. You can request corrections or adaptations*
9. You validate, unequivocally, the proof by email.
10. We confirm and launch the production of your personalized and tailor-made carpet.

Attention :

• Take into account a margin of +- 3 cm on the edges of the image in order to manage tolerances
• Item color and print color may vary from the image shown on screen or on paper.
• You can send us the Pantone/RGB references of your logo to respect the marking colors. Without indication we will use standard colors. Technical deviations from Pantone/RGB colors must be tolerated.
• The BAT proof is sent in 100% real size, unless the dimensions and/or a different percentage are indicated (for example 25%: the final result is therefore 4 times larger).
• Please check the proof carefully. After your approval from the proof, we are no longer responsible for errors in the text and/or logo and/or image.

* In order to avoid abuse, corrections to the BAT are possible within the limit of 3 studies. However, for the less experienced, participation in infographic services could be considered to obtain the desired project.

AVAILABLE COLORS

CODED	COLOR
6021	Black
9489	Anthracite
6012	Gray
327	Medium gray
306	Light gray
295	Beige
415	Orange
651	Gold
292	YELLOW
409	Pale red
6134	Brick red
421	Red
405	Fuchsia
514	Navy blue
052	Light blue
526	Dark blue
523	Blue
524	Turquoise
6025	Mole
619	Grass green
406	Bordeaux
021	Brown
245	Ocher
6115	Light brown
102	White
624	Dark green
605	Forest green
636	Green
623	Green apple

CHOICE OF DOORMAT FRAME

When ordering the custom frame, it is necessary to indicate the external dimensions of the frame . Our technical services will calculate the useful dimensions of the doormat.

In order to compensate for the thickness of the doormat frame, it may be necessary to provide a re-surfacing (Egaline type) of the doormat bottom or a rubber underlay of a few mm, see on this page "RUB - Rubber underlay rubber for entrance doormats"

PROMA-JAN - Aluminum - Natural - Height 16 mm

Frames for entrance doormats in anodized aluminum color, natural color .

Profiles measuring 30 x 16 x 3 mm, the visible upper edge of which is 7 mm.

Profile height: 16 mm - Doormat recess height: 12 mm.

VER-ALU - Aluminum - Natural - Height 16 mm or 21 mm

Frames for entrance doormats in aluminum color, natural color.

Profiles of 21 x 16 mm 3 mm thick. Visible edge of 6 mm.

Profile height: 16 or 21 - Doormat recess height: 10 or 15.

PROMA-AN - Aluminum - Natural - Height 26 mm

Frames for entrance doormats in anodized aluminum color, natural color.

Profiles of 30 x 26 mm, 3 mm thick. Visible edge of 7 mm.

Profile height: 26 mm - Doormat installation height: 22 mm.

PROMA-AR - Aluminum - Stainless steel color - Height 26 mm

Frames for entrance doormats in INOX-colored aluminum.

30/26/3 mm profiles, the visible upper edge of which is 7 mm and fixings.

Profile height: 26 mm - Doormat installation height: 22 mm.

VER-ALU - Aluminum - Natural - Height 26 mm or 31 mm

Frames for entrance doormats in aluminum color, natural color.

Profiles of 31 x 26 mm, 3 mm thick. Visible edge of 6 mm.

Profile height: 26 or 31 mm - Doormat recess height: 20 or 25 mm.

PROMA-AZ - Aluminum - Anthracite Gray Color - Height 26 mm

Frames for entrance doormats in ANTHRACITE GRAY aluminum.

30/26/3 mm profiles, the visible upper edge of which is 7 mm and fixings.

Profile height: 26 mm - Doormat installation height: 22 mm.

VER-BLACK - Black lacquered aluminum - Height 26 or 31 mm

Frames for entrance doormats in black lacquered aluminum.

Profiles of 31/26 or 26/31 mm, the visible upper edge of which is 6 mm.

Profile height: 26 mm or 31 mm - Doormat recess height: 20 mm or 25 mm.

Please note, the thickness of the frame is 6 mm, possibly provide an underlay to compensate for the thickness.

PROMA-MS - Brass - Natural - Height 26 mm

Frames for entrance doormats in natural brass .

30/26/3 mm profiles, the visible upper edge of which is 7mm.

Profile height: 26 mm - Doormat installation height: 22 mm.

VER-LAI - Brass - Height 26 or 31 mm

Frames for entrance doormats in brass-colored aluminum.

Profiles of 31/26 or 26/31 mm, the visible upper edge of which is 6 mm.

Profile height: 26 mm or 31 mm - Doormat recess height: 20 mm or 25 mm.

Please note, the thickness of the frame is 6 mm, possibly provide an underlay to compensate for the thickness.

TEXTILE

• YARN: Solution-dyed continuous filament of type 6 nylon.
• YARN WEIGHT: 1000 gr/m² .
• FIBER LENGTH: 11.3 mm.
• TOTAL WEIGHT: 3.20 kg/m².
• PRIMARY SUPPORT: 120 gr/m² polyester spun non-woven fabric.
• RUBBER BACKING: 100% Nitrile EXS rubber. Compression molded with reinforced edges for excellent dimensional stability and lay flat properties.
• EDGE THICKNESS: 3 mm
• WIDTH OF THE PERIFERAL BAND: 1.5 cm
• TOLERANCE: +/- 2%

HD digital printing is carried out on white fibers, specialized and durable dyes are sprayed directly onto the fibers (like current color printers).

During the drying process, the color fuses to the fibers for maximum hold over time.

The mat or doormat is then vulcanized onto the rubber in order to permanently fix the fibers.

SUPPORT & BACK

Smooth or Claw 3mm rubber sole.

The printed mat can also be glued to the underlay or attached using Velcro or double-sided adhesive, etc. However, this reduces the options for care and maintenance.

ECOLOGICAL FOOTPRINT

The manufacturer is committed to reducing the ecological footprint for the production of its products.

For this reason, the products are made from 100% reusable energy and with local materials.

CLEANING INSTRUCTION

GRAFICSTAR carpets can be cleaned in different ways.

1. They can be laundered commercially (see laundering instructions).
2. Vacuumed regularly (daily in high traffic areas; weekly in low traffic applications).
3. Cleaned with extractor or hosed down as needed to remove heavy dirt. Hang to dry.

Mats must always be dry before being put back into service.

LAUNDRY WASHING INSTRUCTION

• Rinse, 2-3 min. on an average water level with a maximum temperature of 49°C
• Rinse (optional), 2-3 min. on an average water level with a maximum temperature of 49°C
• Break, 2-3 mins. on a high water level with a maximum temperature of 49°C
• Rinse, 2 min. on high water level with cold temperature
• Rinse, 2 min. on high water level with cold temperature
• Extract at low speed, 1-2 min.
• Shake with the rotating drum, 1 min.
• Extract, on a maximum of 250G, 3-5 Min.
• Dry (optional), 5-10 min. with a maximum basket temperature of 82°C
• Cooling, 5 min.

Additional recommendations:

• It can be washed with other SDN rugs.
• For heavily soiled carpets, increase the temperature to max. 71°C.
• The rupture must not exceed a pH of 9.5; use non-ionic, low pH detergents.
• Do not overdry the carpets; The temperature of the dryer basket should not exceed 82°C.
• If the carpets are not dry, the final rinse can be increased to 49°C. This will reduce moisture retention after extraction.
• Lay rugs flat after removing them from the washer; allow mats to cool before rolling.