PrimaFloor - Primer and stain the wood before finishing - Owatrol Pro
Hard bottom insulation and tinted wood component.
Volume discounts
Quantity | You Save | Unit price |
---|---|---|
3 | 5 % | €27.34 |
10 | 8 % | €26.47 |
PrimaFloor - Primer and stain the wood before finishing - Owatrol Pro
Primafloor is a tinted or colorless insulating hard base .
Intended for all types of wood , it standardizes the supports and strengthens the hold of the vitrifier .
Properties :
- Applies to raw wood before vitrification.
- Reinforces the hold of the vitrifier and guarantees an optimum result.
- Insulates the support (especially in the case of tropical woods) before vitrification.
- Yield: Approximately 10 to 12 m² per coat per litre.
Performance may vary depending on the condition of the support, its impregnation and the application equipment. - Monocomponent, ready to use.
- Insensitive to light, does not yellow.
- Slows the formation of stains on woods rich in tannin or natural oil.
Substrate preparation:
- In order to avoid too deep scratches due to sanding, carry out a sanding test with a parquet sander equipped with a grit n° 40 or 50.
- Depending on the visual result obtained, gradually continue with a finer grit up to n° 80 or 100 or start with a coarser grit (grit < 40) for soil that is clogged and not flattened.
- Use a flanging machine for the edges, a scraper or a wood chisel for the angles.
- If necessary, fill cracks < 2 mm with LianFloor and resume sanding with grit n° 80 or 100 depending on the last grit used.
- Finish with finishing sanding up to grit numbers 120 to 150 depending on the species and the thickness of the wear layer.
Professional advice:
- Respect the particle size scale above. It is recommended to skip only one grain at a time.
- Adapt the sanding pressure and speed according to the grain used, the nature of the more or less soft wood and the thickness of the wear layer. Good preparation is essential for the final appearance of the finish.
- Always dust thoroughly with a vacuum cleaner between each sanding without forgetting the dust traps (baseboards, radiators, pipes, edges of bay windows, etc.).
- Formerly oiled or waxed floors: prefer, first, dry stripping with DSP 800 followed by degreasing before sanding (contact us).
- In all cases, comply with the standards/DTU in force.
Application :
- Shake the product well.
- Apply a coat of PrimaFloor making sure the product penetrates well.
- Start with the edges then work the entire surface, working in areas of 2m by 2m.
- Do not open windows during application to avoid too rapid drying.
- The milky aspect of the product will very quickly disappear to become transparent.
- For certain tropical or tannin-rich woods, it is possible to apply two coats of PrimaFloor one hour apart without exceeding 8 hours. This base layer will give a much greater insulating effect.
destinations:
- Parquet floors, floors, interior stairs, new or old.
- Applies to all species.
Conditioning :
1L, 2.5L and 10L.
Data sheet
- Signal word
- As of Q2 2023, no signal word is listed for this item when last checked. Please check the latest update of the technical data sheet issued by the manufacturer.
- Hazard statements
- As of Q2 2023, no hazard statements are listed for this item when last checked. Please check the latest update of the technical data sheet issued by the manufacturer.
- Hazard pictogram
Specific References
- EAN13
- 3297974102268
le produit est très agréable à appliqué et durci correctement le bois . Peut être à bientôt ?
Nous avons déjà utilisé ces produits et sommes entièrement satisfaits. Produits utilisés: Lianfloor Primafloor Végafloor A recommander
Rendu esthétique parfait sur un plancher en pin basique et mise en œuvre assez simple. A conseiller
Facile à appliquer Très satisfait
Produit répondant parfaitement au attentes