WoodGuard AntiGraffiti - Water and oil repellent anti-graffiti for wood - Guard Industrie
WoodGuard AntiGraffiti is a permanent water, oil and stain repellent for untreated or renovated wood.
Volume discounts
Quantity | You Save | Unit price |
---|---|---|
3 | 5 % | €311.27 |
5 | 10 % | €294.89 |
10 | 15 % | €278.50 |
WoodGuard AntiGraffiti - Water and oil repellent anti-graffiti for wood - Guard Industrie
WoodGuard AntiGraffiti is a permanent, water-repellent , oil-repellent and anti-stain anti-graffiti for raw or renovated wood.
It is a new generation product for the protection of raw or renovated wooden cladding.
A two-component product, WoodGuard AntiGraffiti penetrates all wood fibers to protect it sustainably against graffiti, tags of all kinds (paints, markers, etc.), humidity , grease, and stains.
It withstands dozens of cleanings and therefore does not need to be re-applied after removing graffiti.
Advantages
- Permanent anti-graffiti
- Protection against water, oil and stains
- Let the support breathe
- Colorless, available in matte or glossy finish
- Does not distort the structure and natural appearance of the wood
- UV and frost resistant
- Delays aging and easy maintenance
- Won't peel, blister or yellow
Use
- All types of raw wood: pine, spruce, Douglas fir, larch, autoclave wood
- Facades
- New or old
- Outside
- Recommended for cladding, fences, gates, etc.
Implementation
Preparation of the support
- New wood: apply the product to clean, dust-free, healthy and dry wood.
- Gray or oily wood: clean with WoodGuard Conditioner, rinse thoroughly, dust and dry the wood.
- Damaged wood: sand to expose it, then dust and dry the wood.
- Always prepare the wood according to the DTU in force.
- Ensure that the support has all the guarantees of good durability.
Application
- Do not apply in rainy weather or in very high heat.
Ideal air and support temperature 5°C to 30°C. - Carry out a preliminary test in condition on a small, inconspicuous surface and leave to dry for 24 hours, particularly on oily wood and exotic wood. Check adhesion.
- Apply in the direction of the wood fibers.
- Shake product A (base) well before use.
- Slowly add part B (hardener) to part A (base) of WoodGuard AntiGraffiti while stirring.
Stir at moderate speed using an electric mixer until a homogeneous mixture is obtained (5 to 15 minutes depending on the quantity). - Allow the mixture to degas for 15 to 30 minutes in the open air then stir again for 1 minute before use.
- The mixture thus prepared can be used for 6 hours at an ambient temperature below 25°C.
If the temperature is higher, allow a shorter implementation time, around 4 hours.
Do not use the mixture if the time limit has passed.
Application of the 1st pass:
- Apply WoodGuard AntiGraffiti diluted with 5 to 10% water maximum.
- Apply without overloading to avoid creating a thick, non-breathable film.
- Apply if possible to all visible surfaces.
- Leave to dry for 30 minutes to 1 hour at 20°C.
The surface must be dry and not sticky before applying the 2nd coat.
Application of the 2nd pass:
- In the case of bristling wood fibers to obtain a smooth surface, it is possible to sand the surface.
- Apply the second coat without overdoing using WoodGuard AntiGraffiti undiluted.
- On very absorbent wood such as aged wood, a third coat may be necessary.
Allow to dry and follow the same procedure as the second coat. - Protect from rain for 24 hours and from greasy dirt for 48 hours.
- Optimal effectiveness obtained after 5 to 7 days.
Application tools
For better control and perfect control of the result, apply WoodGuard AntiGraffiti preferably using an air-assisted sprayer.
Application by brush is also possible.
Consumption
130 to 265 g/m² for 2 coats.
Conditioning
5 L: Matte or Glossy.
Data sheet
- Signal word
- WARNING
- Hazard statements
- H317 – May cause an allergic skin reaction.
H412 – Harmful to aquatic life with long lasting effects. - Hazard pictogram
-
GHS07 - Harmful
Specific References
- EAN13
- 3461509419989